A Class Anniversary
Some years ago now I worked with one of my favorite editors, Kara Gott Warner, and the folks at Annie’s Craft Store to develop an online class, Colorwork Without the Work. The class covers simple ways to work with color in stripes: basic stripe patterns worked flat and in the round, helix knitting, mosaic knitting (stripes with slipped stitches to make patterns!), and vertical intarsia stripes. As a project-based class, it also includes tutorials on techniques like working from a temporary cast-on, grafting in garter stitch, reading charts, and three-needle join.
This week I’m celebrating the anniversary of the class release with a post on stripes, specifically three-color one-row stripes worked flat, something I didn’t cover in class. Work the swatch coaster and you will also learn how to work the e-loop cast-on and work a sewn bind-off.
Grab three colors of DK or worsted weight cotton and US 5-6 needles, and let’s make some stripes!
Normally when we knit flat we work in pairs of rows: out then back, odd row/even row, RS row then WS row. Working one-row stripes in two colors requires working with double-ended needles and using a special move called the slide. Add a third color, however, and there’s no special needles or moves required. The yarn you need to use next will always be waiting for you on the other side.
Have a read through the coaster instructions, and then scroll to the skills section to get started!
Use this project to stretch your color muscles! Pull out your color wheel and use it to select a color triad. Or choose a key color and its split complementary hues. Or make it a study in light and dark: choose a hue, and a tint and tone.
Colorful Striped Coasters
4-5 g each worsted weight cotton in 3 colors A, B, C
US 6 needles
tapestry needle, scissors
With A and using e-loop cast-on, cast on 20 sts. Leaving tail of B, join B and knit one row. Leaving tail of C, join C and knit one row.
Row 1: With A, knit.
Row 2: With B, knit.
Row 3: With C, knit.
Repeat rows 1-3 until piece is square (check by folding one corner of the cast-on edge diagonally up to the needle; if it meets the end stitch then the piece is square), approximately 4 inches from cast-on.
Cut the last yarn used and the one on the far end, leaving 4-6 inch tails. Leaving a tail 3-4 times the width of the piece, cut the yarn for binding off and thread on tapestry needle. Using sewn bind-off, bind off.
The e-loop or loop cast-on is not my favorite cast-on but it is the right one for imitating a one row stripe. Be sure to hold the tail tightly as you cast on the first few stitches as they tend to want to fall off the needle. Use the same caution when you work into those loops on your first real row.
Join B And C
Turn the work as usual at the end of the A cast-on. Leave a tail of B and with B, knit across the row. Turn the work. Leave a tail of C and with C, knit across the row. The working yarns for C and A will be at one end, and B at the other. As you continue working back and forth, use the yarn that is next in the sequence (A, B, C) and which should be waiting for you as you finish the current row.
When you get to the end of a row there will always be two yarns at that end, the one you just used and the one you need to use next. To switch to the new yarn, simply drop the one you just used and let it hang where it falls. Pick the new one up and take it to the back to begin knitting or to the front to begin purling.
Binding Off: Sewn Bind-Off
Leaving a tail 3-4 times as long as the piece is wide, cut the yarn you will use for the sewn bind-off and thread it through a tapestry needle. Hold the work in one hand and with the other, *insert the tapestry needle purlwise and right to left through the first two stitches, pull yarn through. Insert the tapestry needle knitwise from left to right through the first stitch, then slip this stitch off the knitting needle. Repeat from * , adjusting tension of the sewn stitches to match the fabric, until all stitches have been slipped off.
Want More Stripes??
Take a stripes class with me at STITCHES Salt Lake!
I’ll be teaching Stripes of the Circular Type on Thursday, October 3, 2019 from 9-noon. You will learn how to carry yarns up the inside, minimize “the jog,” try helix knitting, and make mobius stripes. I’ll also talk about principles of contrast and repetition, and strategies for creating your own stripe patterns. Let’s make stripes in the round! Learn more here.